Pneumatic Round Cylinders
A. Round cylinder, double-acting DSNU
Wide range of variants for customised applications
Good running performance and long service life
Self-adjusting pneumatic end-position cushioning saves time during commissioning and adapts optimally to load and speed changes
Piston rod with female or male thread
For position sensing
B. Round cylinder DSNU-S
Short variant of ISO cylinder DSNU
Quick and easy installation, even in tight spaces
Light weight
Self-adjusting pneumatic end-position cushioning saves time during commissioning and adapts optimally to load and speed changes
Piston rod with male thread
For position sensing
Variants recommended for production systems for manufacturing lithium-ion batteries
Sustainable in production thanks to reduced use of materials
C. Round cylinder CRDSNU
Corrosion resistant against aggressive ambient conditions
Easy-to-clean design
Long service life thanks to optional dry-running seal
Wide range of variants for customised applications
Self-adjusting pneumatic end-position cushioning saves time during commissioning and adapts optimally to load and speed changes
D. Round cylinder, single-acting ESNU
Wide range of variants for customised applications
Good running performance and long service life
Piston rod with female or male thread
For position sensing
E. Round cylinder CRHD
Corrosion resistant against aggressive ambient conditions
Easy-to-clean design, optimised for very exacting demands
Flexible design thanks to different end caps
Piston rod with male thread
For position sensing
F. Round cylinder EG-PK
Micro cylinder
Barbed fitting for plastic tubing with standard I.D.
Without position sensing
Reference:
Profile cylinder and tie rod cylinder
A. Standards-based cylinder DSBC
ISO 15552 (ISO 6431, VDMA 24562)
Self-adjusting pneumatic end-position cushioning saves time during commissioning and adapts optimally to load and speed changes
Standard profile with two sensor slots
Wide range of variants for customised applications
Comprehensive range of mounting accessories for just about every type of installation
For position sensing
Variants recommended for production systems for manufacturing lithium-ion batteries
B. Standards-based cylinder CRDNG
ISO 15552 (ISO 6431, VDMA 24562)
Corrosion resistant against aggressive ambient conditions
Easy-to-clean design
Variants: through piston rod, heat-resistant design
Threaded mounting, mounting via accessories
For position sensing
C. Standards-based cylinder DSBF
ISO 15552
Increased corrosion protection
Easy-to-clean design
FDA-approved lubrication and sealing on the basic version
Long service life thanks to optional dry-running seal
Self-adjusting pneumatic end-position cushioning saves time during commissioning and adapts optimally to load and speed changes
For position sensing
D. Standards-based cylinder DSBG
ISO 15552 (ISO 6431, VDMA 24562)
Sturdy tie rod design
Self-adjusting pneumatic end-position cushioning saves time during commissioning and adapts optimally to load and speed changes
Comprehensive range of mounting accessories for just about every type of installation
For position sensing
Reference:
Compact pneumatic cylinders, short-stroke and flat cylinders
A. Compact cylinder, double-acting ADN
ISO 21287
Up to 50% less installation space than comparable standards-based cylinders to ISO 15552
Piston rod with female or male thread
Wide range of variants for customised applications
For position sensing
Variants recommended for production systems for manufacturing lithium-ion batteries
B. Compact cylinder, double-acting ADN-S
Minimal installation space
Very lightweight
Ideal for small movements
Piston rod with female or male thread
For position sensing
Variants recommended for production systems for manufacturing lithium-ion batteries
Sustainable in production thanks to reduced use of materials
C. Compact cylinder ADN-EL
ISO 21287
With end-position locking at both ends, front or rear
Piston rod with female or male thread
For position sensing
D. Compact cylinder, single-acting AEN
ISO 21287
Up to 50% less installation space than comparable standards-based cylinders to ISO 15552
Piston rod with female or male thread
Wide range of variants for customised applications
For position sensing
E. Flat cylinder, metric DZF
Extremely flat design
Protected against rotation thanks to special piston shape
Ideal for manifold assembly
Wide variety of mounting and attachment options
Piston rod with female or male thread
For position sensing
F. Flat cylinder, metric DZH
Flat design
Protected against rotation thanks to special piston shape
Ideal for manifold assembly
Wide variety of mounting and attachment options
Piston rod with male thread
For position sensing
G. Flat cylinder EZH
Extremely flat design
Protected against rotation thanks to special piston shape
Wide variety of mounting and attachment options
For position sensing
H. Compact cylinder DPDM
Mounting using through-hole and female thread
Compact design
Piston rod variants
For position sensing
Sustainable in production thanks to reduced use of materials
Reference:
Multimount and pin cylinders
A. Compact cylinder DPDM
Mounting using through-hole and female thread
Compact design
Piston rod variants
For position sensing
Sustainable in production thanks to reduced use of materials
B. Cartridge cylinder EGZ
Minimal installation space
Installation with or without mounting components
Piston rod with male thread
Reference:
Rodless Cylinder
A. Linear drive DGC
Basic design, plain or ball bearing guide, guide axis without actuator
All settings accessible from one side
Available with variable end stops and intermediate position module
Optional: NSF-H1 lubricant for the food zone (see www.festo.com/certificates/DGC)
Optional: clamping unit for holding loads
Sustainable operation thanks to leakage reduction at sealing points
B. Linear drive Rodless Cylinder DGC-K
Compact design: 30% smaller than basic design DGC-G
Basic drive without guide, for simple drive functions
Low moving dead weight
Symmetrical design
Reference:
Standard O.D. tubing
We supply a wide range of O.D. pneumatic tubing. A popular product from our Core Range is the Plastic Tubing PUN-H which can be very successfully combined with OS fittings. It is made of polyurethane and is available in 14 different colours and as a single or double tube. It has excellent kink resistance and can be used flexibly, even in the food industry, thanks to the high quality material. The PUN-H is particularly resistant to microbes and hydrolysis, making it ideal for laying lines quickly and reliably.
Technical details:
A. Plastic tubing PUN-H, PUN-H-DUO
Polyurethane
High resistance to microbes and hydrolysis
Suitable for use with energy chains
Clean room-compatible combination with fitting NPKA
Also available as DUO plastic tubing
Operating media compressed air, vacuum, water. Water as per the manufacturer’s declaration, see www.festo.com/certificates/PUN_H
Plastic Tubing PUN-H
B. Plastic tubing PAN
Polyamide
High thermal and mechanical load capacities
Highly resistant to microbes
Operating medium: compressed air, vacuum
Plastic Tubing PAN
C. Plastic tubing PAN-MF
Polyamide
High thermal and mechanical load capacities
Meets the requirements to DIN 73378 “Polyamide tubing for use in motor vehicles”
Operating media: compressed air, mineral oil
Plastic Tubing PAN MF
D. Heavy-duty tubing PAN-R
Polyamide
For applications with high pressure ranges
Highly resistant to microbes
Operating medium: compressed air, vacuum
Plastic Tubing PAN-R
Spiral tubing
A. Spiral plastic tubing PPS
The thermally and mechanically highly resilient, hydrolysis-resistant spiral plastic tubing PPS is supplied ready for connection, with two swivel fittings and captive sealing rings OL.
Polyamide, brass, galvanised steel
Pre-assembled with 2 rotatable connectors and captive sealing rings OL
Highly resistant to microbes
Operating medium: compressed air, vacuum
Spiral Tubing PPS
B. Spiral plastic tubing PUN-S, PUN-S-DUO
The single or dual tubing PUN-S/PUN-S-DUO with straight outlets is flexible in use, extremely elastic and has an unbeatable reset force for motion sequences in machines. The pre-assembled solution PUN-SG has rotatable threaded outlets for the supply of compressed air tools.
Polyurethane
Also available as DUO plastic tubing
Operating medium: compressed air, vacuum
High resistance to UV radiation and stress cracks
Spiral Tubing PUN-S
C. Spital Plastic Tubing PUN-G
The single or dual tubing PUN-S/PUN-S-DUO with straight outlets is flexible in use, extremely elastic and has an unbeatable reset force for motion sequences in machines. The pre-assembled solution PUN-SG has rotatable threaded outlets for the supply of compressed air tools.
Polyurethane, nickel-plated brass, polyacetal
Pre-assembled with captive rotatable fittings
High resistance to microbes and hydrolysis
Operating medium: compressed air, vacuum
Spiral Tubing PUN-SG
Pneumatic Fittings
A. Push-in fitting
Standard series
Wide range of variants: wide selection for maximum flexibility in standard applications
PBT and nickel-plated brass
Operating media compressed air, vacuum, water. Water as per the manufacturer’s declaration, see www.festo.com/certificates/QS
Straight shape, L-shape, T-shape, at 45° angle, X-shape, Y-shape, push-in bulkhead connector
B. Cartridge
C. Fluid Separator
D. Push-in Fitting Metal NPQM
E. Push-in Fitting NPQE
F. Push-in Fitting NPQH
G. Push-in Fitting QSM
H. Push-in cartridge QSP
I. Push-in Cartridge QSPK
J. Push-in Fitting, resistant to media, NPQP
K. Push-in Fitting, resistant to welding spatter, QS-V0
L. Push-in Fitting Stainless Steel NPQR
Click fitting NPKA
The light, corrosion-free polymer in click fitting NPKA is free of non-ferrous metal, fluoride, silicone and grease, FDA-conform and suitable for cleanrooms. Ideal for the electronics and semi-conductor industry, small parts and battery cell assembly or for food and beverages production.
POM, polyamide 66
Quick and easy one-handed tube installation
Completely made of polymer
Food grade see www.festo.com/certificates/NPKA
Operating media compressed air, vacuum, water. Water as per the manufacturer’s declaration, see www.festo.com/certificates/NPKA
No copper, fluor or silicone
Cleanroom compatible
Easy-to-clean design with few corners and edges
Straight design, L-shaped, T-shaped
Threaded Pneumatic Fittings
A. Threaded fitting NPFC
Brass, nickel-plated
Sleeve
Extension
Double nipple
Reducing nipple
Operating medium: compressed air, vacuum
Straight shape, L-shape, T-shape, X-shape, Y-shape
Threaded Fittings NPFC
B. Ring piece and hollow bolt LK, TK, VT
Multiple distributor consisting of hollow bolt VT and ring piece LK or TK
With two to six outlets and one common air feed
Operating medium: compressed air, vacuum
Galvanised steel
Ring piece and Hollow bolt
C. Reducing nipple
Threaded Fitting Reducer
D. Distributor FR
E. Adapter NPFV
F. Sleeve QM
G. Double Nipple
Double Nipple
Solenoid valve for individual connection VUVG
This universal valve has been newly designed on the inside and now offers an outstanding combination of high flow rates and a compact design. The entire VUVG range, as an individual valve or a valve terminal, is designed to cater precisely for all your requirements.
Compact universal valve
Connection technology via electrical connection box (E-box)
High flow rate relative to its size
In-line valves can be used as individual valves or manifold valves
Reference:
Solenoid valve VUVS
Sturdy solenoid valve that is easy to operate
Universal valve, sturdy and durable
Low cost with no performance limitations
Can be used as individual valves or manifold valves VTUS
Reference:
A. Solenoid valve VSNC
The standard NAMUR valve VSNC is certified in accordance with the most common explosion standards the world over. It is a sturdy unit that combines great value for money with a modern design.
Namur connection pattern to VDI/VDE 3845
Rotatable seal for 3/2- or 5/2-way valve
Wide choice of EX solenoid systems
Sturdy and powerful
Extended temperature range
Excellent value for money
All solenoid coils can be used on an armature tube
The VSNC-…FN variant achieves greater energy efficiency with reduced power consumption
B. Standards-based valve with central plug VSVA
Standards-based valves ISO 15407-1 with central plug.
Conforms to ISO 5599-1
Electrical connection with central plug
Robust metal housing
Manifold assembly with mixed sizes possible
Catalog
C. Standards-based valve with individual plug VSVA
Corresponds to ISO 15407-1 and to ISO 15218 for pilot valve with interface
Electrical connection via plug type C
Robust metal housing
Manifold assembly with mixed sizes possible
Catalog
D. Standards-based valve, plug-in VSVA
For valve terminal VTSA/VTSA-F
Robust metal housing
Catalog
E. Standards-based valve to ISO 5599-1, electrically actuated
Conforms to ISO 5599-1
Robust metal housing
Manifold assembly with mixture of ISO sizes 1, 2 and 3 possible
Extensive range of electrical connection options
Wide range of vertical stacking modules: pressure regulator, flow control valve, vertical pressure shut-off plate, etc.
Also available as a valve terminal
Catalog
F. Standards-based valve VSCS
Valve actuator for electrical actuation of valve bodies
CNOMO connection pattern, to ISO 15218
Detenting or non-detenting manual override
Catalog